• Frost 20L Rust free Drinking Fountain

     

    • Efficient Cooling: The hygienic rust-free tank provides a cooling capacity of 20 liters per hour, maintaining water temperatures between 8-12°C.
    • Hygienic Design: The integrated drip tray features a drainage system to prevent water accumulation and ensure cleanliness.
    • User-Friendly: Equipped with two faucets, allowing direct drinking from the bubbler or filling a cup with filtered cold water.
    • Inline Filtration System: Ensures clean, great-tasting water by removing impurities with quick change Sediment and Carbon Cartridges (included).

    Cold Water Supply
    		20L/H (8-12°C)     |
    Cold Water Temp
    8-12°C
    Cooling Power
    		200W
    Filter Activated Carbon, PP Sediment
    Refrigerant  R290 60g
    Measurements 99cm H x 30cm W x 30cm D
    Bubbler Height 7cm
    Tap Height
    		25cm

    Unpack

    1. After unpacking the water cooler, wipe with a soft cloth. Check the unit for evidence of rough handling.
    2. Place the machine on a hard, flat surface. Make certain the unit is level. The unit should not be close to sources of heat otherwise performance may be affected.

    Install

    1. Follow the instructions for setting up the Tri-Stage Refillable Bottle on the product page here.
    2. Ensure proper ventilation be allowing 75 mm clearance on each side of the fountain.
    3. Place water bottle on top of unit and allow tank to fill.
    4. Hold down the taps until a steady stream of water comes from the tap.
    5. Check all connections for water leaks.
    6. Flush fresh water through unit for five minutes to ensure any residual water from testing is cleared.
    7. Plug the cooler into the building electrical supply and for the cook and cold model: Switch to the ON position. The first time the water cooler is used, you will have to wait at least 45 minutes for cold and hot water.

    Data_Sheet User_Manual Drinking_Water_Solutions

    June 17, 2025|, , |

  • Frost 20L SS Cylinder Drinking Fountain

    Ensure reliable access to refreshing, cold water with our Commercial Stainless Steel Cold Water Bubbler. Crafted from premium SUS304 stainless steel, this water cooler fountain is built to withstand the demands of busy environments while maintaining the highest standards of hygiene.

    • Efficient Cooling: The hygienic stainless-steel tank provides a cooling capacity of 20 liters per hour, maintaining water temperatures between 8-12°C.
    • Hygienic Design: The integrated drip tray features a drainage system to prevent water accumulation and ensure cleanliness.
    • Durable Construction: All SUS304 stainless steel welded frame and exterior panels ensure longevity and resistance to corrosion.

    Cold Water Supply
    		20L/H(8-12°C)
    Cold Water Temp
    8-12°C
    Material
    		Stainless Steel SUS304
    Power Supply 220-240V / 50-60Hz
    Refrigerant  R290 60g
    Bubbler Height 7cm

    Unpack

    1. After unpacking the water cooler, wipe with a soft cloth. Check the unit for evidence of rough handling.
    2. Place the machine on a hard, flat surface. Make certain the unit is level. The unit should not be close to sources of heat otherwise performance may be affected.

    Install

    1. Follow the instructions for setting up the Tri-Stage Refillable Bottle on the product page here.
    2. Ensure proper ventilation be allowing 75 mm clearance on each side of the fountain.
    3. Place water bottle on top of unit and allow tank to fill.
    4. Hold down the taps until a steady stream of water comes from the tap.
    5. Check all connections for water leaks.
    6. Flush fresh water through unit for five minutes to ensure any residual water from testing is cleared.
    7. Plug the cooler into the building electrical supply and for the cook and cold model: Switch to the ON position. The first time the water cooler is used, you will have to wait at least 45 minutes for cold and hot water.

    Data_Sheet User_Manual Drinking_Water_Solutions

    March 7, 2025|, |

  • Frost 20L SS Square Drinking Fountain

    Ensure reliable access to refreshing, cold water with our Commercial Stainless Steel Filtered Cold Water Bubbler. Crafted from premium SUS304 stainless steel, this water cooler fountain is built to withstand the demands of busy environments while maintaining the highest standards of hygiene.

    • Durable Construction: All SUS304 stainless steel welded frame and exterior panels ensure longevity and resistance to corrosion.
    • Efficient Cooling: The hygienic stainless-steel tank provides a cooling capacity of 20 liters per hour, maintaining water temperatures between 8-12°C.
    • Hygienic Design: The integrated drip tray features a drainage system to prevent water accumulation and ensure cleanliness.
    • User-Friendly: Equipped with two faucets, allowing direct drinking from the bubbler or filling a cup with filtered cold water.
    • Inline Filtration System: Ensures clean, great-tasting water by removing impurities with quick change Sediment and Carbon Cartridges (included).

     

    Cold Water Supply
    		20L/H (8-12°C)
    Cold Water Temp
    8-12°C
    Cooling Power
    		200W
    Filter Activated Carbon, PP Sediment
    Material Stainless Steel SUS304
    Measurements 99cm H x 30cm W x 30cm D
    Bubbler Height 7cm
    Tap Height
    		25cm

    Unpack

    1. After unpacking the water cooler, wipe with a soft cloth. Check the unit for evidence of rough handling.
    2. Place the machine on a hard, flat surface. Make certain the unit is level. The unit should not be close to sources of heat otherwise performance may be affected.

    Install

    1. Follow the instructions for setting up the Tri-Stage Refillable Bottle on the product page here.
    2. Ensure proper ventilation be allowing 75 mm clearance on each side of the fountain.
    3. Place water bottle on top of unit and allow tank to fill.
    4. Hold down the taps until a steady stream of water comes from the tap.
    5. Check all connections for water leaks.
    6. Flush fresh water through unit for five minutes to ensure any residual water from testing is cleared.
    7. Plug the cooler into the building electrical supply and for the cook and cold model: Switch to the ON position. The first time the water cooler is used, you will have to wait at least 45 minutes for cold and hot water.

    Data_Sheet User_Manual Drinking_Water_Solutions

    March 7, 2025|, |

  • Heavy Duty Drinking Fountain – Grey Powdercoat

    The M Series is a sleek, mains-connected water fountain with a heavy-duty build. The tank is made from industrial-grade stainless steel ensuring the fountain will meet any demand.

    • Industrial grade 304 stainless steel tank and robust construction
    • Polished stainless steel top
    • Front panel removes for ease of servicing
    • Optional stainless steel cabinets
    • Simple filter changes for filtered units
    • Adjustable, tamper-proof, non-squirt bubbler and glass filler
    • IP33 rating suitable for outdoor use

    M Series Dark Grey Powdercoat M Series Stainless Steel

    Data Sheet User Manual Ingress Protection

    May 27, 2025|, , , |

  • M Series Drinking Fountain – Stainless Steel

    The M Series is a sleek, mains-connected water fountain with a heavy-duty build. The tank is made from industrial-grade stainless steel ensuring the fountain will meet any demand.

    • Industrial grade 304 stainless steel tank and robust construction
    • Polished stainless steel top
    • Front panel removes for ease of servicing
    • Optional stainless steel cabinets
    • Simple filter changes for filtered units
    • Adjustable, tamper-proof, non-squirt bubbler and glass filler
    • IP33 rating suitable for outdoor use

    M Series Dark Grey Powdercoat M Series Stainless Steel

    Data Sheet User Manual Ingress Protection

    March 7, 2025|, , , |

  • Drinking Fountain – M Series Wall Mounted

    The wall-mounted WM Series is especially designed for areas where floor space is restricted. Suitable for mounting at any height makes them ideal for children or people in wheelchairs.

    • 19L/h chilling capacity – suitable for 1-40 people
    • Industrial grade 304 stainless steel tank and robust construction
    • Polished stainless steel top
    • Front panel removes for ease of servicing
    • Adjustable, tamper proof non-squirt water bubbler and drink bottle/glass filler
    • Australian WaterMark Certification (Lic No. WMK26317)

    WM Series Dark Grey Powdercoat

    Data Sheet User Manual Ingress Protection

    March 7, 2025|, , |